Ji Donglai was in charge of pushing the cart, and Li Baoping didn't say much. Instead, he inspected every size of the workpiece step by step. The two of them detected the key points on the drawings.
Because the inspection was done in reverse order of processing, Ji Donglai's last step was to inspect the primary processing of the pump body. At this step, Ji Donglai's eyes almost dropped.
The workers in the workshop almost drove the ordinary lathe. The iron filings on the cast iron pump body fell like snow flakes. The workers were so fast in their operations.
According to the requirements of the process design card, the other party needed three cuts to follow up gradually, and the amount of cutting for each cut should not be too large. As a result, the workshop workers directly turned the cutter into position, and left the rest to the finishing CNC machine tool.
After processing a basket of products, the workers would sit on the chairs in front of them and rest for twenty minutes, then get on the car again and continue driving.
"Master Li, isn't this speed a bit too fast?"
Seeing that the workers were not performing the processing process according to the process cards, Ji Donglai subconsciously looked at Li Baoping, who was testing the damping holes. He raised his head in surprise when he heard what Ji Donglai said.
"Can you understand the processing drawings?"
Putting down the pump body in his hand, Li Baoping looked around, put the car in the designated area, and took Ji Donglai into the lounge.
"Well, I have relatives who work in factories. I grew up with them, so I know a little bit about it!"
Holding the blueprint process card, Ji Donglai looked through the various processing techniques of a pump body on site from front to back, and finally found that the workers on site violated more than one of them. Strictly speaking, almost none of them were followed.
According to the requirements of the process card, the processing of the pump body stop and the inner cavity is completed by two machine tools. In the second step, a tooling fixture is required. During on-site processing, the workshop workers now finish the work directly on a lathe without any tooling for alignment, which means that the concentricity on the seam side is lost.
Even if there is later finishing machining for alignment, the pump body will still have the risk of a certain side wall thickness being out of tolerance, which is absolutely not allowed in industrial processing.
As for those high-pressure pump bodies, the surfaces are machined and the interior is milled, but they are not tooled as required. This is very abnormal.
At the very least, the concentricity of the bearings cannot be guaranteed. If you meet an experienced craftsman, there will be no problem. If you are a little negligent, the quality of this product will almost freeze. .br>
"Remember here to talk less, read more, and listen more! I really feel that this place is not good. Remember not to stay here. Look at the people in the workshop. They all have to stay here. There are really No one would choose to stay here!"
"Besides, the boss doesn't make money from this, you know? The boss now hopes that this processing plant will go bankrupt, and then these old employees will resign, so he can sell this land, do you understand?"
"Can't we see what you can see? You will know when you go to the pump body finished product workshop. There are also our quality inspectors there, and they are also inspecting. Can't they detect this kind of fault? They can, But everyone has reached a tacit understanding, no one cares anymore!”
"You are going to join the technical department in the future. Don't compete with these people in the workshop. Don't you tell anyone what you said today clearly? It's easy to be caught by people who are interested. This factory is much better than what you see. The water is much deeper!"
Li Baoping unscrewed the plastic water cup and took a sip of water. Ji Donglai couldn't help being surprised and secretly thought that he had done the right thing.
He quickly took out a small bag of tea leaves from his pocket and gave it directly to Li Baoping. The supplier gave it to Ji Donglai, and Ji Donglai gave it all to Li Baoping this time.
The other party was very helpful, and then began to educate Ji Donglai about the past and present life of this factory.
Li Baoping has been an intern in this factory for 20 years since he was 18 years old. This processing factory was originally profitable. Even if it encountered an economic crisis, the factory could still maintain a balance of income and expenditure.
It was the other two companies that lost money, including the foundry, which happened to coincide with the privatization of state-owned enterprises.
In order to privatize these properties, Zhang Qinglu teamed up with the leaders of several other factories to transfer all the debts to Jichuan Pump Industry, and then split the entire company.
The remaining bosses were debt-free and spent a small price to buy the factory and move it to other places for production and processing.
, Zhang Qinglu successfully obtained the trademark and land use rights of Jichuan Pump Industry.
According to the agreement, the severance pay for each worker in the factory was 100,000 plus. Zhang Qinglu wanted to pay less, but the workers never agreed. After all, it was a large sum of money.
The number of workers on the account is 300. To pay all the compensation, Zhang Qinglu will have to spend at least 30 million.
Now that the value of the factory land is rising, Zhang Qinglu is worried, so he keeps hiring new general managers to negotiate with the workers, but with little success.
Zhang Qinglu then changed his strategy and relied on time!
Some elderly people in the factory have underlying diseases. After the factory was privatized, the heating was owned by the heating company. The heating was not good, and the workers were very cold in winter.
In the summer, almost all the electric fans in the company's workshop were broken. Even if they could blow, they would not have much cooling effect.
In this way, the old workers couldn't bear it anymore and had no choice but to resign.
Since ancient times, where has there been any compensation for resigning? Dismissal and factory dismissal are two different concepts, and many people have no choice but to do so.
Last year, Zhang Qinglu once again came up with the idea of a loss. The whole factory adopts a piece-rate model for all parts. Take today's pump body, the price of processing one piece is two yuan.
Every process was priced, and the factory almost went crazy. The subsequent processes are the finishing touches of the previous processes, and the prices are very low. In order to earn more, the workers at the back even go to the lathe workshop to urge them.
Unreasonable execution of processing technology will inevitably lead to a rapid decline in product quality. Now the product quality of the entire factory can no longer be described as poor.
The best way to destroy the factory is to destroy the brand. Originally, the steering pump and oil pump of Jichuan Pump Industry were designated products of the local BAIC. Now the market share is getting lower and lower. If it is not fixed in a few years, it will return to zero. .
At that time, the workers can only accept the fact that the factory is bankrupt, and the land will be auctioned off as a matter of course. But Zhang Qinglu is now taking advantage of the factory's continuous loans. As for the flow of funds, only the devil knows.
There is only one thing that the outside world knows now: the quality of this factory's products cannot be controlled.
Of course, Zhang Qinglu is still thinking about one thing: sell the product, and then transfer the money through international lawsuits and compensation.
The last conclusion was analyzed by Ji Donglai himself, not given by Li Baoping.
Combining Li Baoping's explanation to Ji Donglai, and Zhang Qinglu seeking Ji Donglai's help in selling such poor quality products, and searching through his own memory, this conclusion was reached almost instantly.
